Kee Klamp Safety Railing Fittings

Electronic Payments

Unistrut Buffalo Supports

Kee Klamp Safety Railing Systems

A simple, effective solution for added safety

For the last 75 years Kee Safety has been a leading manufacturer of top quality safety solutions from protection for loading docks or safety walkways in factories, to safety barriers in aggressive coastal environments to the protection of road bridges and culverts.

Kee Safey systems provide simple, modular soltions that are cost effective, flexible and efficient to install.

View More
10-Kee-Klamp-Single-Socket-Tee.jpg
No. 10 - Kee Klamp Single Socket Tee

Designed to give a 90° butt joint between two pipes. Frequently used for the joint between end uprights and the middle rail on safety railing where the site is straight and level. Also for base ties on racking. This fitting cannot be used where the pipe through sleeve 'A' is required to be joined within the fitting. Type 25 should be used when a join in the pipe is necessary.

More Info
---
Choose Options
View More
A10-Kee-Klamp-Split-Single-Socket-Tee.jpg
No. A10 - Kee Klamp Split Single Socket Tee

Designed to allow additions or extensions to existing structures without the need for dismantling. Pipe must not be joined within the fitting. Fitting has strength and function comparable to Type 10 fittings.

More Info
---
Choose Options
View More
A12-Kee-Klamp-Split-45-degree-Single-Socket-tee.jpg
No. A12 - Kee Klamp Split 45 Degree Single Socket Tee

The unique "Hinge and Pin" system of this fitting enables existing structures to be easily extended without the need for dismantling. This fitting is most frequently used for bracing and struts.

More Info
---
Choose Options
View More
12-Kee-Klamp-45-degree-Single-Socket-Tee.jpg
No. 12 - Kee Klamp 45 Degree Single Socket Tee

Most frequently used for bracing and struts.

More Info
---
Choose Options
View More
14-Kee-Klamp-Straight-Coupling.jpg
No. 14 - Kee Klamp Straight Coupling

Designed to form an inline joint between two pieces of pipe of the same size. Where a constant diameter is required along the outside of the pipe (such as for ADA handrail or garment storage), an internal spigot (Type 18) should be considered.

More Info
---
Choose Options
View More
15-Kee-Klamp-90-Degree-Elbow.jpg
No. 15 - Kee Klamp 90 Degree Elbow

A 90° elbow joint, most frequently used as an end joint for the top rail of safety railing on a level site.

More Info
---
Choose Options
View More
16-Kee-Klamp-Clamp-On-Tee.jpg
No. 16 - Kee Klamp Clamp-On Tee

Widely used for adding to and modifying existing structures. This performs the same function as a Type 10, but because of its open socket, it can be added to a complete structure. For alternative fitting, see type A10. Type 25 should be used when a join in the pipe is necessary.

More Info
---
Choose Options
View More
17-Kee-Klamp-Clamp-On-Crossover.jpg
No. 17 - Kee Klamp Clamp-On Crossover

Designed to provide a 90° cross-over joint. Can be added to an existing structure. Pipe should not be joined within this fitting. For alternative fitting, see Type 45 or Type A45.

More Info
---
Choose Options
View More
18-Kee-Klamp-Internal-Coupling.jpg
No. 18 - Kee Klamp Internal Coupling

An internal spigot providing a flush joint between two pipes of the same diameter. Not as strong as Type 14 and must not be used where a direct tensile load is applied. This fitting can only be used with Schedule 40 steel pipe.

 
Danger: Type 18 fitting must not be used as a load bearing joint
More Info
---
Choose Options
View More
19-Kee-Klamp-Adjustable-Side-Outlet-Tee.jpg
No. 19 - Kee Klamp Adjustable Side Outlet Tee

Used in pairs to form variable angle joints between 90° and 180°. When calculating cutting lengths for pipe, dimension 'E' should be subtracted to give true pipe length. In the case of Type 19-8 and Type 19-85, you can produce an angle range between 60° and 180°.

Type 19 fittings are normally used in pairs. In the USA and Canada, they are sold and priced in pairs.
More Info
---
Choose Options
View More
20-Kee-Klamp-Side-Outlet-Elbow.jpg
No. 20 - Kee Klamp Side Outlet Elbow

A 90° corner joint most frequently used for the top rail of safety railing. It can also be considered for the corner joint of benches, work tables, and other rectangular structures.

More Info
---
Choose Options
View More
21-26-Split-90-Degree-Side-Outlet-Tee-Split-Two-Socket.jpg
No. 21 - Kee Klamp 90 Degree Side Outlet Elbow

Most frequently paired with Type 20 to give a 90° corner joint for the middle rail of safety railing and other rectangular structures. The upright passes through the fitting.

More Info
---
Choose Options
View More
25-Kee-Klamp-Three-Socket-Tee.jpg
#25 - Kee Klamp Three Socket Tee

 

Most commonly used as the 90° joint between the top rail and an intermediate upright on safety railing. As there are two socket set screws in the sleeve, this fitting can be used where a join is required in the horizontal pipe. The Type 10 fitting can be used as an alternative when a join in the pipe is not required.
More Info
---
Choose Options
View More
26-Kee-Klamp-Two-Socket-Cross.jpg
No. 26 - Kee Klamp Two Socket Cross

Usually paired with Type 25 to give a 90° joint between the middle rail and an intermediate upright on safety railing. The upright passes through the fitting.

More Info
---
Choose Options
View More
kk_27_wht.jpg
No. 27 - Kee Klamp 0 Degree to 49 Degree Three Socket Custom Tee

Used for safety railing on slopes between 0º and 45º, between the top rail and an intermediate upright which is required to remain vertical. Components are held in stock as blanks and then machined to individual requirements. These fittings are held in stock as blanks which are machined to individual requirements. Special order only; please specify required angle.

More Info
---
Choose Options
View More
kk_28_wht.jpg
No. 28 - Kee Klamp 0 Degree to 45 Dgree Three Socket Custom Cross

Used for safety railing on slopes between 11º and 30º, between the midrail and an intermediate upright which is required to remain vertical. These fittings are held in stock as blanks which are machined to individual requirements. Special order only; please specify required angle.

More Info
---
Choose Options
View More
29-Kee-Klamp-30-Degree-To-60-Degree-Single-Socket-Tee.jpg
No. 29 - Kee Klamp 30 Degree to 60 Degree Single Socket Tee

Designed as an alternative to the Type 12 fitting, this adjustable fitting is most frequently used for bracing and struts. It may be used at any selected angle between 30° and 60°. As an alternative, it is possible to use Type 29 in its vertical position in place of the Type 27, using the Type 27 only where a join in the pipe occurs.

More Info
---
Choose Options
View More
30-Kee-Klamp-30-Degree-To-45-Degree-Adjustable-Cross.jpg
No. 30 - Kee Klamp 30 Degree to 45 Degree Adjustable Cross

Designed as an alternative to the Type 28 fitting, this adjustable fitting can be used for railing on staircases between the midrail and an intermediate upright which is required to remain vertical. It may be used at any selected angle between 30° and 45°.

More Info
---
Choose Options
View More
30-Kee-Klamp-Pallet-Flange.jpg
No. 31 - Kee Klamp Pallet Flange

This fitting has been designed for the construction of post pallets. Incorporates sockets for the upright and side pipes, and a locating bell for stacking pallets. (Special Order Only)

More Info
$60.45
Buy
View More
A35-Kee-Klamp-Split-Three-Socket-Cross.jpg
No. A35 - Kee Klamp Split Three Socket Cross

The unique "Hinge and Pin" system of this fitting, enables existing structures to be easily extended without the need for dismantling. This fitting has been designed to tie an upright with horizontal pipes in three directions, all at 90° to the upright. The upright passes through the fitting.

More Info
---
Choose Options
View More
35-Kee-Klamp-Three-Socket-Cross.jpg
No. 35 - Kee Klamp Three Socket Cross

Most frequently used to tie uprights with horizontal pipes in three directions, all at 90° to the upright. The upright passes through the fitting.

More Info
---
Choose Options
View More
40-Kee-Klamp-Four-Socket-Cross.jpg
No. 40 - Kee Klamp Four Socket Cross

Most frequently used in multiple upright structures to tie a center upright with horizontal pipes in four directions. The upright passes through the fitting.

More Info
---
Choose Options
View More
A40-Kee-Klamp-Split-Four-Socket-Cross.jpg
No. A40 - Kee Klamp Split Four Socket Cross

The unique "Hinge and Pin" system of this fitting enables existing structures to be easily extended without the need for dismantling. This fitting is most frequently used in multiple upright structures to tie a center upright with horizontal pipes in four directions. The upright passes through the fitting.

More Info
---
Choose Options
View More
A45-Kee-Klamp-Split-Crossover.jpg
No. A45 - Kee Klamp Split Crossover

The unique "Hinge and Pin" system of this fittings enables existing structures to be easily extended without the need for dismantling. This fitting is designed to give a 90° offset crossover joint. Pipe should not be joined within the fitting. Type A45 function is comparable to Type 45 fittings.

More Info
---
Choose Options
View More
45-Kee-Klamp-Crossover.jpg
No. 45 - Kee Klamp Crossover

Designed to give a 90° offset crossover joint. Frequently used on safety railing, where, to reduce cost by minimizing the pipe cuts, a continuous horizontal rail is used. Pipe cannot be joined within this fitting. It may be also used to give intermediate levels on racks, etc, when horizontal ties between uprights across the section are not required.

 
Where Dimension 'E' indicates two figures, the first figure refers to socket 'A' and the second refers to socket 'B' in the table.
More Info
---
Choose Options
View More
46-Kee-Klamp-Combination-Socket-Tee-and-Crossover.jpg
No. 46 - Kee Klamp Combination Socket Tee and Crossover

Used on racking to join horizontal carrying rails to the upright, leaving the socket to take a horizontal tie across the section. For shelved racking it is usual to have the horizontal pipe outside the upright. On pallet racking it is preferable to have the carrying rails inside the upright.

More Info
---
Choose Options
View More
C50-Kee-Klamp-Single-Swivel-Socket.jpg
No. C50 - Kee Klamp Single Swivel Socket

Complete combination fitting. Reducing combinations of Type C50 are available sizes 5 through 9. See types F50 and M50 for individual fitting specifications. See "SWIVEL FITTINGS" box on page 13 for more information.

More Info
---
Choose Options
View More
M50-Kee-Klamp-Male-Single-Swivel-Socket-Member.jpg
No. M50 - Kee Klamp Male Single Swivel Socket Member

One part of a combination fitting. This can also be used for attaching flat panels to tubular structures. Ø indicates diameter of bolt hole.

 
Type M50-4 will only mate with a type F50-4.
More Info
---
Choose Options
View More
MH50-Male-Horizontal-Single-Swivel-Socket-Member.jpg
No. MH50 - Kee Klamp Male Horizontal Single Swivel Socket Member

This fitting can be used for attaching flat panels to tubular structures. Specially designed for retail shelving applications. Can also be used as part of a Type CH50 combination fitting. Ø indicates diameter of bolt hole.

More Info
$8.64
Buy
View More
P50-Kee-Klamp-Modified-M50-8-With-Offset-Slot.jpg
No. P50 - Kee Klamp - Offset Double Tab Panel Fitting with Slot

 

Designed for the securing of various types of panels and flooring to pipe structures. (i.e. plywood, plastic sheeting, wood planking etc.). This fitting has one offset flange to allow the flush attachment of panels to pipe. Often used with Type P51. See also Type P57.
More Info
$12.55
Buy
View More
MH51-Kee-Klamp--Male-Horizontal-Double-Swivel-Socket-Member.jpg
No. MH51 - Kee Klamp Male Horizontal Double Swivel Socket Member

This fitting can be used for attaching flat panels to tubular structures. Specially designed for retail shelving applications, the MH51 can be used as part of a Type CH51 combination fitting.

More Info
$15.65
Buy
View More
P51-Kee-Klamp-Modified-M51-8-With-Offset-Slots.jpg
No. P51 - Kee Klamp - Offset Double Tab Panel Fitting with Slot

Designed for the secure fitting of various types of panels and flooring to pipe structures (i.e. plywood, plastic sheeting, wood planking, etc.) This fitting has two offset flanges to allow the flush attachment of panels to pipe.

More Info
$19.72
Buy
View More
M51-Kee-Klamp-Male-Double-Swivel-Socket-Member.jpg
No. M51 - Kee Klamp Male Double Swivel Socket Member

One part of a type C51 combination fitting. This fitting can also be used for attaching flat panels to tubular structures. Ø indicates diameter of bolt holes.

More Info
---
Choose Options
View More
C51-Kee-Klamp-Double-Swivel-Socket.jpg
No. C51 - Kee Klamp Double Swivel Socket

Complete combination fitting. Type C51 is made by combining two Type F50 fittings and one Type M51. For dimensions refer to Type F50 and Type M51. See "SWIVEL FITTINGS" box on page 13 for more information.

More Info
---
Choose Options
View More
C52-Kee-Klamp-Corner-Swivel-Socket.jpg
No. C52 - Kee Klamp Corner Swivel Socket

Complete combination fitting. Reducing combinations of Type C52 are available, sizes 5 to 8. For dimensions refer to Type F50 and Type M52. See "SWIVEL FITTINGS" box on page 13 for more information.

More Info
---
Choose Options
View More
M52-Kee-Klamp-Male-Corner-Swivel-Socket-Member.jpg
No. M52 - Kee Klamp Male Corner Swivel

One part of a Type C52 combination fitting. This fitting can also be used for attaching flat panels to tubular structures. Ø indicates diameter of bolt hole.

More Info
---
Choose Options
View More
55-Kee-Klamp-Obtuse-Angle-Elbow.jpg
No. 55- Kee Klamp Obtuse Angle Elbow

The Type 55 is an ideal fitting to use as an alternative to bending, or when a junction between a sloping pipe and an end post is required - i.e., guardrailing and staircases.

More Info
---
Choose Options
View More
56-Kee-Klamp-Acute-Angle-Elbow.jpg
No. 56 - Kee Klamp Acute Angle Elbow

Type 56 is an ideal fitting to use as an alternative to bending, or when a junction between a sloping pipe and an end post is required - i.e., guardrailing and staircases.

More Info
---
Choose Options
View More
P57-Kee-Klamp-Modified-M50-With-Slot.jpg
No. P57 - Kee Klamp Modified M50 with Slot

Designed for the securing of various types of panels and flooring to pipe structures (i.e. plywood, plastic sheeting, wood planking, etc.). This fitting has a single offset flange to allow for the attachment of panels to pipe. See Type P50.

More Info
---
Choose Options
View More
M58-Kee-Klamp-Swivel-Flange-Plate.jpg
No. M58 - Kee Klamp Swivel Flange Plate

This fitting may be considered for various wall and brace fixings. It is often combined with Type F50 to give an adjustable angle fitting Type C58. Ø indicates diameter of base plate fixing holes. The diameter of the attachment bolt hole is 0.39 inch (10mm).

More Info
$11.60
Buy
View More
59-Kee-Klamp-Spigot-Flange.jpg
No. 59 - Kee Klamp Spigot Flange

A spigot flange which fits inside the pipe and is not secured by a set screw. Type 59 can only be used with pipe wall thickness of 1/8" and in light, self supporting structures. Type 59 is manufactured in aluminum.

 
No fixing holes are provided in this fitting.
More Info
---
Choose Options
View More
60-Kee-Klamp-Extra-Heavy-Flange.jpg
No. 60 - Kee Klamp Extra Heavy Flange

A heavy duty flange, with wide base, for spreading loads over a large surface area. This flange, with holes provided for countersunk flat head screw fixings only, is for use on structures where the fixing required is positional only. Frequently used as a wall fixing bracket. Ø indicates diameter of fixing holes.

 
It is not recommended for use as a base flange to support guardrailing or balustrading.
More Info
---
Choose Options
View More
61-Kee-Klamp-Flange.jpg
No. 61 - Kee Klamp Flange

This flange, with holes provided for countersunk flat head screw fixings only, is used on structures where the fixing required is positional only. Frequently used as a wall fixing bracket. Ø indicates diameter of fixing holes

 
It is not recommended for use as a base flange to support guardrailing or balustrading.
More Info
---
Choose Options
View More
62-Kee-Klamp-standard-Railing-Flange.jpg
No. 62 - Kee Klamp Standard Railing Flange

Ideal when a structural fixing is required. When fixing guardrailing and balustrades, Type 62 should always be used. The holes are of sufficient diameter to insure proper fixing with either a mechanical or chemical anchor. The two set screws in the vertical socket give greater sideload stability to the upright. It is recommended that the fixing holes in the flange should be in line with the applied load. Ø indicates diameter of fixing holes.

More Info
---
Choose Options
View More
63-Angle-Base-Flange.jpg
No. 63 - Kee Klamp Angle Base Flange

This fitting is similar to Type 62, but is used to set up the upright at an angle between 45° to 60°. This fitting should only be subjected to light loads, which cannot be positioned at 90° to the applied load. For greater loads or other pipe sizes, a Type 62 flange is used and the upright bent to the required angle. Ø indicates diameter of fixing holes.

More Info
---
Choose Options
View More
64-Kee-Klamp-Standard-Vertical-Railing-Base.jpg
No. 64 - Kee Klamp Standard Vertical Railing Base

This fitting is designed for fixing guardrailing and balustrading to walls, parapets, steps and ramps. The upright cannot drop through the socket. Access to the top fixing hole is restricted by the position of the flange to the barrel. When selecting a hexagon head bolt or similar bolt fixing, the maximum length of the bolt including the head must not exceed 1". (Refer to table on page 35).

 
Should an upright be required to pass through the fitting, the base can be bored out to order. Ø indicates diameter of fixing holes.
More Info
---
Choose Options
View More
65-Kee-Klamp-Standard-Horizontal-Railing-Base.jpg
No. 65 - Kee Klamp Standard Horizontal Railing Base

This fitting is designed for palm fixing guardrailing and balustrading to walls, parapets, steps and ramps. Only available in size 6. The upright cannot drop through the socket. Ø indicates diameter of fixing holes.

Should an upright be required to pass through the fitting, the base can be bored out to order.

More Info
$26.69
Buy
View More
66-Kee-Klamp-Ground-Socket.jpg
No. 66 - Kee Klamp Ground Socket

A ground socket fitting for setting in concrete; the posts may either be permanent or removable as required. It incorporates a socket set screw fixing and can be supplied with a plug to fill the hole when the pipe is removed.

More Info
---
Choose Options
View More
67-Kee-Klamp-Angle-Flange.jpg
No. 67 - Kee Klamp Angle Flange

Type 67 has been designed to allow the upright to pivot in the barrel, providing an angular displacement from 3° up to a maximum of 11°, measured from the vertical. Ideal to secure balustrade and guardrail systems on access ramps or other types of slopes. Ø indicates diameter of fixing holes.

 
It is generally recommended that when installing the 67-8, the fixing holes in the base should be in line with the applied load.
More Info
---
Choose Options
View More
68-Kee-Klamp-Wall-Flange.jpg
No. 68 - Kee Klamp Wall Flange

Side fixing for guardrailing and balustrading to walls, parapets, steps and ramps. The upright cannot drop through the socket. Ø indicates diameter of fixing holes.

 
If the upright is required to pass through the fitting by machining out the base stop, the bottom fixing hole will be unusable.
More Info
---
Choose Options
View More
69-Kee-Klamp-Railing-Flange-With-Toeboard-Adaptor.jpg
No. 69 - Kee Klamp Base Flange and Kick Plate

The Type 69 fitting has been designed for guardrailing and balustrading applications and provides the added benefit of attaching a toeboard to the base. The base plate holes are of sufficient diameter to allow for attachment with either a mechanical or chemical anchor, the side plates have slotted holes to allow for a degree of sideways movement for ease of installation. A toeplate designed for use with the Type 69 fitting is available from Kee Industrial Products. Ø indicates diameter of fixing holes.

More Info
---
Choose Options
View More
70-Kee-Klamp-rail-Support.jpg
No. 70 - Kee Klamp Rail Support

This fitting, with holes provided for countersunk flat head screw fixings only, is designed to carry handrails along walls or to fix structures back to walls. The pipe passes through the fitting and cannot be joined within the fitting. Type 70 is also used to attach toeboards to the base of guardrail uprights. Ø indicates diameter of fixing holes.

 
These fittings are not to be used as base flanges for full height guardrails.
More Info
---
Choose Options
View More
71-Kee-Klamp-Weather-Cap.jpg
No. 71 - Kee Klamp Weather Cap

Type 71 is a weather cap designed for roof guardrailing to ensure a weathertight seal for base fixing flanges. The weather cap is secured to the upright by means of a combined sealant and adhesive.

More Info
---
Choose Options
View More
72-Kee-Klamp-Stair-Tread-Support.jpg
No. 72 - Kee Klamp Standard Tread Support

 

Type 72 is a stair tread support suitable for most types of stair tread, including timber, open steel and checker plate. Fixing of the treads is by two bolt holes in each fitting. Ø indicates diameter of fixing holes. (Special Order Only)
 
If Type 72 fittings are to be used for a permanent application or subjected to high loads, the stair tread support pipe which is located at its ends with a single set screw, should be drilled and pinned to avoid rotational slip.
More Info
$44.12
Buy
View More
75-Kee-Klamp-Collar.jpg
No. 75 - Kee Klamp Collar

A collar commonly used to support another fitting if the latter is required to be left untightened, such as on gate hinges. Type 75 is also useful when the loading on a structure exceeds the maximum permitted slip load for a set screw, as it gives extra support.

More Info
---
Choose Options
View More
76-Kee-Klamp-Hook.jpg
No. 76 - Kee Klamp Hook

A fitting normally used for attachment of chains.

More Info
---
Choose Options
View More
78-Kee-Klamp-Eye-Fitting.jpg
No. 78 - Kee Klamp Eye Fitting

A fitting used in conjunction with Type 83 fitting for gate hinges. Ø indicates diameter of pivot hole.

More Info
---
Choose Options
View More
79-Kee-Klamp-Sheeting-Clip.jpg
No. 79 - Kee Klamp Sheeting Clip

 

This fitting is used to attach profiled sheeting material to pipe. The fitting is supplied with the following hardware: one M6x50mm roofing bolt, one M6 square nut, and one M6 lock washer. BZP finish. Ø indicates diameter of bolt hole.
More Info
$2.57
Buy
View More
81-Kee-KLamp-Single-Sided-Clip.jpg
No. 81 - Kee Klamp Single Sided Clip

Single clips for attaching wire-mesh infilling. For economy it is possible to use Type 81 clips without the safety attachment, to secure various types of infill panels (plyboard, perspex, etc.) up to a thickness of 25/64". All clips are supplied with hexagonal head fixing bolts, M6x35mm long, and nut.

More Info
---
Choose Options
View More
82-Kee-Klamp-Double-Sided-Clip.jpg
No. 82 - Kee Klamp Double Sided Clip

Double clips for attaching wire-mesh infilling. For economy it is possible to use Type 82 clips without the safety attachment, to secure various types of infill panels (plyboard, perspex, etc.) up to a thickness of 25/64". All clips are supplied with hexagonal head fixing bolts, M6x35mm long, and nut. Ø indicates diameter of the safety attachment bolt hole. The primary clip has a slot measuring 8mm x 15mm.

More Info
---
Choose Options
View More
83-Kee-Klamp-Pin-Fitting.jpg
No. 83 - Kee Klamp Pin Fitting

This fitting is used in conjunction with Type 78 for gate hinges.

More Info
---
Choose Options
View More
84-Kee-Klamp-Malleable-Plug.jpg
No. 84 - Kee Klamp Malleable Plug

A metal drive-in plug which is difficult to remove when installed. For an alternative in plastic, see Type 77.

 
This fitting can only be used with Schedule 40 steel pipe.
More Info
---
Choose Options
View More
86-Kee-Klamp-Angle-Tee.jpg
NO. 86 - Kee Klamp Angle Tee

Used to join the middle rail to an end upright on a guardrail on a slope from 0° to 11°. Pipe cannot be joined within this fitting.

More Info
---
Choose Options
View More
87-Kee-Klamp-Angle-Elbow.jpg
No. 87 - Kee Klamp Angle Elbow

Used to join the top rail to an end upright on a guardrail on a slope from 0° to 11° at both top and bottom of the run.

More Info
---
Choose Options
View More
88-Kee-Klamp-Three-Socket-Angle-Tee.jpg
No. 88 - Kee Klamp Three Socket Angle Tee

Used to join the top rail to an intermediate upright on a guardrail on a slope from 0° to 11°. As there are two socket set screws in the sleeve, this fitting can be used to join two ends of rail.

More Info
---
Choose Options
View More
89-Kee-Klamp-Two-Socket-Angle-Cross.jpg
No. 89 - Kee Klamp Two Socket Angle Cross

Used to join the middle rail to an intermediate upright on a guardrail on a slope from 0° to 11°. The upright passes through the fitting.

More Info
---
Choose Options
View More
90-PGR-Kee-Klamp-PGR-Three-Socket-Tee.jpg
No. 90 - Kee Klamp PGR Three Socket Tee

Type 90 is used to join the top rail to an intermediate upright. (Special Order Only)

More Info
$55.73
Buy
View More
91-PGR-Kee-Klamp-PGR-Two-Socket-Cross.jpg
No. 91 - Kee Klamp PGR Two Socket Cross

Type 91 is used to join the midrail to an intermediate upright. (Special Order Only).

More Info
$53.83
Buy
View More
92-PGR-Kee-Klamp-PGR-Elbow.jpg
No. 92 - Kee Klamp PGR Elbow

Type 92 is used to join the top rail to an end post. (Special Order Only)

More Info
$39.20
Buy
View More
93-PGR-Kee-Klamp-PGR-Tee.jpg
No. 93 - Kee Klamp PGR Tee

Type 93 is used to join the midrail to an end post. (Special Order Only).

More Info
$43.20
Buy
View More
95-PGR-Klee-Klamp-PGR-Interan-Spigot.jpg
No. 95 - Kee Klamp PGR Internal Spigot

Internal spigot designed to prevent sagging of bends when using the 90 to 95 range of fittings. (Special Order Only).

 
This spigot can only be used with Schedule 40 steel pipe.
More Info
$57.44
Buy
View More
105-Kee-Klamp-Sheeting-Clip-With-Out-Hardware.jpg
No. 105 - Kee Klamp Sheeting Clip with out Hardware

This fitting is used to attach profiled or flat sheeting. It is not supplied with hardware. Ø indicates diameter of bolt hole.

More Info
---
Choose Options
View More
114-Kee-Klamp-Swivel-Tee.jpg
No. 114 - Kee Klamp Swivel Tee

An internal swivel fitting, designed to accommodate varying angles on handrailing for staircases, ramps, or bracing. Used in conjunction with Types 10, 15, 25 or 45, it eliminates the need for specially drilled angle fitting Type 27 and Type 28.

More Info
---
Choose Options
View More
115-Kee-Klamp-Wall-Flange.jpg
No. 115 - Kee Klamp Wall Flange

Type 115 is designed for palm fixing of guardrailing and balustrading to walls, parapets, steps and ramps. The upright cannot drop through the socket. Packer Plates (Type S115) are available to allow the fitting to be positioned in channels, slots, and other offset areas. Ø indicates fixing hole diameter.

More Info
---
Choose Options
View More
118-Kee-Klamp-Cover-Flange.jpg
No. 118 - Kee Klamp Cover Flange

The Cover Flange slips over uprights to finish below ground post installations. The fitting is secured to the upright pipe with a single recessed grubscrew.

More Info
---
Choose Options
View More
121-Kee-Klamp-Corner-Crossover.jpg
No. 121 - Kee Klamp Corner Crossover

This fitting is designed to provide a 90 degree offset corner joint. When calculating the cutting lengths for pipe, dimension 'G' should be subtracted to give the pipe length for the rails and dimension 'H' should be added to give the pipe length for the upright.

More Info
$34.65
Buy
View More
327-Kee-Klamp-3-Socket-Tee.jpg
No. 327 - Kee Klamp Three Socket Custom Tee

Similar to a type 27, it is used on Safety Railing with slopes between 11º–30º and fixes the top rail to a vertical intermediate upright. Unlike the type 27 these components do not require machining.

More Info
---
Choose Options
View More
328-Kee-Klamp-2-Socket-Cross.jpg
No. 328 - Kee Klamp Two Socket Custom Cross

Similar to a type 28, it is used on Safety Railing with slopes between 11º–30º and fixes the mid rail to a vertical intermediate upright. Unlike the type 28 these components do not require machining.

More Info
---
Choose Options
View More
351-Kee-Klamp-Ridge-Fitting.jpg
No. 351 - Kee Klamp Ridge Fitting

The Type 351 fitting has been designed for small structural building applications and provides for significant load rating. When used with the Type 350 eave fitting a truss arrangement for additional support can be achieved. Double set screws are provided on the downward truss outlet to provide additional pull out resistance and extra strength to the structure.

More Info
$28.83
Buy
View More
C53_Kee-Klamp-Adjustable-Three-Way-Swivel-Socket.jpg
No. C53 - Kee Klamp Swivel Elbow

A swivel fitting for attachment of angled pipe to a flat surface. For dimensions refer to Type F50 and Type M58.

 
It is not recommended for use as a base flange to support guardrailing, balustrading or other types of structure.
More Info
---
Choose Options